![]() It seems that adding "-s" to the registered uninstall string "C:\Program Files (x86)\InstallShield Installation Information\\setup.exe" -runfromtemp -l0x0009 -removeonly" can work. So, I started looking for a way to uninstall version 4.80 silently before installing version 6.10, and chaining those two steps in a script. The installer will not remove an older version their only advice is to manually remove the older version before installing the newer. I contacted Logitech support on this matter. I found keys such as "LaunchParameters" and "LaunchSilentParameters" that looked promising, but I could not get anything out of them, especially without any official reference from Logitech. ![]() I have been examining the "compcfg.ini" files, trying to make sense out of them. However, version 4.80 does not get uninstalled and there seems to be a mix up between both versions, with 4.80 staying in the system tray. This seems to work: version 6.10 gets installed. So I have fallen back to the original installer with "setpoint610_圆4.exe /s". Inside that folder, I run the command "setup.exe /s". I downloaded the "setpoint610_圆4.exe" installer and extracted the "5-SetPoint" subfolder. My first approach is to try the same as with version 4.80. Now, we want to upgrade to SetPoint 6.10, which is the only version currently downloadable from Logitech's website. This was easy because #1 I found the silent switch easily ("setup.exe /s", this was an InstallShield package) and #2 no older version of the software was ever present on the workstations. This worked great, using a combination of Microsoft Deployment Toolkit (MDT) for new bare metal workstations and Microsoft System Center Essentials (SCE, which uses WSUS to serve custom packages in addition to regular Microsoft updates) to deploy to workstations already in use. ![]() Inside that folder, I ran the command "setup.exe /s" to install silently. I downloaded the "setpoint480_圆4.exe" installer and extracted the "1-SetPoint" subfolder (using any archive manager, such as 7-Zip). When we started using SetPoint, I was able to deploy version 4.80 to all computers in an unattended manner. We currently use the Logitech SetPoint software version 4.80 under 64-bit Windows Vista. Need more help? see Knowledge Base article 23480 for how to contact Logitech Customer Care about this product.For uniformity, we use Logitech MX Revolution mice at every desks in the company. Move the receiver to a different USB port on your computer Move the mouse or keyboard closer to the USB receiver Keep other electrical devices at least 8 inches (20 cm) away from the USB receiver If this solution doesn't work after a couple of attempts, restart your computer and try the reconnection process again. Click Yes and then Next.Ĭlick Finish to exit the Logitech Unifying Software. When your mouse is detected, you'll see the confirmation message below. When the Logitech Unifying Software Welcome screen displays, click Next to continue.įollow the on-screen instructions to turn your mouse off and then back on. Windows: Start > Programs > Logitech > Unifying > Logitech Unifying Software.To reconnect your mouse to a Windows computer:ĭownload the correct version of Logitech SetPoint mouse and keyboard software from the M325 Downloads page. Plug the receiver directly and securely into a working USB port on your computer. The power indicator should now turn green. If the power indicator is not lit, move the power switch on the bottom of the mouse to the "ON" position. The power indicator on top should be green. For instructions on changing your mouse battery, see Knowledge Base article 23493. Radio frequency (RF) interference from more powerful devices such as:īefore you connect your mouse to a Windows computer:įix or rule out the potential problem sources listed above.Using your cordless mouse on metal surfaces.Plugging the USB receiver into a hub or other unsupported device such as a KVM switch ( NOTE: Your Unifying USB receiver must be plugged directly into your computer.).Moving the USB receiver to another computer.Moving the USB receiver from one port to another.The connection between the mouse and the USB receiver can be lost for several reasons, such as: If your mouse isn't working, the problem is likely a lost connection.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |